This set of plans will take you Step-By-Step to build your own DIY Drum Sander! This is a simple project for any level DIYER! These Drum Sander Plans include a 15-page STEP-BY-STEP PDF document including a material list, cutting layouts, printable templates, SketchUp File, and CNC Files (SVG + DWG). These plans are very thorough, but if you ever have any questions feel free to email us! We have a full build video on this project on YouTube, which you can watch here: https://www.youtube.com/watch?v=EoV8c7KxgYs&t=1269s Digital Download Only! What’s Included: -15-Page PDF that includes all instructions needed to build this sander. -1 Page PDF Printable templates for complex parts. -Full SketchUp File -SVG + DXF Files of all major parts What materials are used? • (1) 48″ x 96″ x 3/4″ Melamine • (1) 24” x 48” x 1/4” MDF • (1) 24” x 48” x 1/2” MDF • (1) 24” x 48” x 3/4” MDF • (~50) Pin Nails or Finish Nails • (~40) 1 1/4” Powerhead Fast Cap Screws - https://amzn.to/2O2Fnmu (affiliate link) • (~30) Misc small screws • (1) Piano Hinge 24” - https://amzn.to/3f2ygoV (affiliate link) • (1 or 2) 3-1/2” Pulley - This depends on what motor you have and what pulleys you may already have. Size of pulley is beyond the scope of these plans. I used an 1800RPM motor with two 3-1/2” pulleys. https://amzn.to/304vZp7 (affiliate link) • (1) 3/4” x 36” Keyed Shaft - If you can find a shorter one that will work. This was what I could find affordably. https://amzn.to/39wrtmc (affiliate link) • (1) Adjustable V-Belt - https://amzn.to/2X1vtWN (affiliate link) • (1) 3/16” key stock 24” - https://amzn.to/2DdrYWc (affiliate link) • (2) Pillow Block Flange Bearings 3/4” - https://amzn.to/39zL19t (affiliate link) • (1) Power Switch - https://amzn.to/3hC3JQo (affiliate link) • (1) 1/2” Threaded Rod 9” Long - I found this at my local ACE hardware. https://amzn.to/2CSNqA9 (affiliate link) • (1) 1/2” Nut and Wing Nut • (8) 7/16” x 2” Bolts and Nylon Lock Nut • (1) Electric Motor - We used an old 1/2HP Blower motor at 1800RPM. This is a good alternative that’s new. You will likely want a small pulley on the motor to slow the drum speed down. a 2” pulley should be good. https://amzn.to/302Naas (affiliate link) • (1 roll) PVC Edge Banding - Optional. To hide the Melamine edges. https://amzn.to/302KVny (affiliate link) • (1) Wood glue - Titebond 2 is what we used but, any wood glue works. https://amzn.to/3hHDNDb (affiliate link)
This set of plans will take you Step-By-Step to build your own DIY Drum Sander! This is a simple project for any level DIYER! These Drum Sander Plans include a 15-page STEP-BY-STEP PDF document including a material list, cutting layouts, printable templates, SketchUp File, and CNC Files (SVG + DWG). These plans are very thorough, but if you ever have any questions feel free to email us! We have a full build video on this project on YouTube, which you can watch here: https://www.youtube.com/watch?v=EoV8c7KxgYs&t=1269s Digital Download Only! What’s Included: -15-Page PDF that includes all instructions needed to build this sander. -1 Page PDF Printable templates for complex parts. -Full SketchUp File -SVG + DXF Files of all major parts What materials are used? • (1) 48″ x 96″ x 3/4″ Melamine • (1) 24” x 48” x 1/4” MDF • (1) 24” x 48” x 1/2” MDF • (1) 24” x 48” x 3/4” MDF • (~50) Pin Nails or Finish Nails • (~40) 1 1/4” Powerhead Fast Cap Screws - https://amzn.to/2O2Fnmu (affiliate link) • (~30) Misc small screws • (1) Piano Hinge 24” - https://amzn.to/3f2ygoV (affiliate link) • (1 or 2) 3-1/2” Pulley - This depends on what motor you have and what pulleys you may already have. Size of pulley is beyond the scope of these plans. I used an 1800RPM motor with two 3-1/2” pulleys. https://amzn.to/304vZp7 (affiliate link) • (1) 3/4” x 36” Keyed Shaft - If you can find a shorter one that will work. This was what I could find affordably. https://amzn.to/39wrtmc (affiliate link) • (1) Adjustable V-Belt - https://amzn.to/2X1vtWN (affiliate link) • (1) 3/16” key stock 24” - https://amzn.to/2DdrYWc (affiliate link) • (2) Pillow Block Flange Bearings 3/4” - https://amzn.to/39zL19t (affiliate link) • (1) Power Switch - https://amzn.to/3hC3JQo (affiliate link) • (1) 1/2” Threaded Rod 9” Long - I found this at my local ACE hardware. https://amzn.to/2CSNqA9 (affiliate link) • (1) 1/2” Nut and Wing Nut • (8) 7/16” x 2” Bolts and Nylon Lock Nut • (1) Electric Motor - We used an old 1/2HP Blower motor at 1800RPM. This is a good alternative that’s new. You will likely want a small pulley on the motor to slow the drum speed down. a 2” pulley should be good. https://amzn.to/302Naas (affiliate link) • (1 roll) PVC Edge Banding - Optional. To hide the Melamine edges. https://amzn.to/302KVny (affiliate link) • (1) Wood glue - Titebond 2 is what we used but, any wood glue works. https://amzn.to/3hHDNDb (affiliate link)
This set of plans will take you Step-By-Step to build your own DIY Drum Sander! This is a simple project for any level DIYER! These Drum Sander Plans include a 15-page STEP-BY-STEP PDF document including a material list, cutting layouts, printable templates, SketchUp File, and CNC Files (SVG + DWG). These plans are very thorough, but if you ever have any questions feel free to email us! We have a full build video on this project on YouTube, which you can watch here: https://www.youtube.com/watch?v=EoV8c7KxgYs&t=1269s Digital Download Only! What’s Included: -15-Page PDF that includes all instructions needed to build this sander. -1 Page PDF Printable templates for complex parts. -Full SketchUp File -SVG + DXF Files of all major parts What materials are used? • (1) 48″ x 96″ x 3/4″ Melamine • (1) 24” x 48” x 1/4” MDF • (1) 24” x 48” x 1/2” MDF • (1) 24” x 48” x 3/4” MDF • (~50) Pin Nails or Finish Nails • (~40) 1 1/4” Powerhead Fast Cap Screws - https://amzn.to/2O2Fnmu (affiliate link) • (~30) Misc small screws • (1) Piano Hinge 24” - https://amzn.to/3f2ygoV (affiliate link) • (1 or 2) 3-1/2” Pulley - This depends on what motor you have and what pulleys you may already have. Size of pulley is beyond the scope of these plans. I used an 1800RPM motor with two 3-1/2” pulleys. https://amzn.to/304vZp7 (affiliate link) • (1) 3/4” x 36” Keyed Shaft - If you can find a shorter one that will work. This was what I could find affordably. https://amzn.to/39wrtmc (affiliate link) • (1) Adjustable V-Belt - https://amzn.to/2X1vtWN (affiliate link) • (1) 3/16” key stock 24” - https://amzn.to/2DdrYWc (affiliate link) • (2) Pillow Block Flange Bearings 3/4” - https://amzn.to/39zL19t (affiliate link) • (1) Power Switch - https://amzn.to/3hC3JQo (affiliate link) • (1) 1/2” Threaded Rod 9” Long - I found this at my local ACE hardware. https://amzn.to/2CSNqA9 (affiliate link) • (1) 1/2” Nut and Wing Nut • (8) 7/16” x 2” Bolts and Nylon Lock Nut • (1) Electric Motor - We used an old 1/2HP Blower motor at 1800RPM. This is a good alternative that’s new. You will likely want a small pulley on the motor to slow the drum speed down. a 2” pulley should be good. https://amzn.to/302Naas (affiliate link) • (1 roll) PVC Edge Banding - Optional. To hide the Melamine edges. https://amzn.to/302KVny (affiliate link) • (1) Wood glue - Titebond 2 is what we used but, any wood glue works. https://amzn.to/3hHDNDb (affiliate link)
Homemade Drum Sander: We actually made it and it works! A drum sander has been on our need/want list for a very long time and we are thrilled that we DIY'd it! This homemade drum sander is going to help out so much and make sanding less awful. You can watch the video bel…
This set of plans will take you Step-By-Step to build your own DIY Drum Sander! This is a simple project for any level DIYER! These Drum Sander Plans include a 15-page STEP-BY-STEP PDF document including a material list, cutting layouts, printable templates, SketchUp File, and CNC Files (SVG + DWG). These plans are very thorough, but if you ever have any questions feel free to email us! We have a full build video on this project on YouTube, which you can watch here: https://www.youtube.com/watch?v=EoV8c7KxgYs&t=1269s Digital Download Only! What’s Included: -15-Page PDF that includes all instructions needed to build this sander. -1 Page PDF Printable templates for complex parts. -Full SketchUp File -SVG + DXF Files of all major parts What materials are used? • (1) 48″ x 96″ x 3/4″ Melamine • (1) 24” x 48” x 1/4” MDF • (1) 24” x 48” x 1/2” MDF • (1) 24” x 48” x 3/4” MDF • (~50) Pin Nails or Finish Nails • (~40) 1 1/4” Powerhead Fast Cap Screws - https://amzn.to/2O2Fnmu (affiliate link) • (~30) Misc small screws • (1) Piano Hinge 24” - https://amzn.to/3f2ygoV (affiliate link) • (1 or 2) 3-1/2” Pulley - This depends on what motor you have and what pulleys you may already have. Size of pulley is beyond the scope of these plans. I used an 1800RPM motor with two 3-1/2” pulleys. https://amzn.to/304vZp7 (affiliate link) • (1) 3/4” x 36” Keyed Shaft - If you can find a shorter one that will work. This was what I could find affordably. https://amzn.to/39wrtmc (affiliate link) • (1) Adjustable V-Belt - https://amzn.to/2X1vtWN (affiliate link) • (1) 3/16” key stock 24” - https://amzn.to/2DdrYWc (affiliate link) • (2) Pillow Block Flange Bearings 3/4” - https://amzn.to/39zL19t (affiliate link) • (1) Power Switch - https://amzn.to/3hC3JQo (affiliate link) • (1) 1/2” Threaded Rod 9” Long - I found this at my local ACE hardware. https://amzn.to/2CSNqA9 (affiliate link) • (1) 1/2” Nut and Wing Nut • (8) 7/16” x 2” Bolts and Nylon Lock Nut • (1) Electric Motor - We used an old 1/2HP Blower motor at 1800RPM. This is a good alternative that’s new. You will likely want a small pulley on the motor to slow the drum speed down. a 2” pulley should be good. https://amzn.to/302Naas (affiliate link) • (1 roll) PVC Edge Banding - Optional. To hide the Melamine edges. https://amzn.to/302KVny (affiliate link) • (1) Wood glue - Titebond 2 is what we used but, any wood glue works. https://amzn.to/3hHDNDb (affiliate link)
This set of plans will take you Step-By-Step to build your own DIY Drum Sander! This is a simple project for any level DIYER! These Drum Sander Plans include a 15-page STEP-BY-STEP PDF document including a material list, cutting layouts, printable templates, SketchUp File, and CNC Files (SVG + DWG). These plans are very thorough, but if you ever have any questions feel free to email us! We have a full build video on this project on YouTube, which you can watch here: https://www.youtube.com/watch?v=EoV8c7KxgYs&t=1269s Digital Download Only! What’s Included: -15-Page PDF that includes all instructions needed to build this sander. -1 Page PDF Printable templates for complex parts. -Full SketchUp File -SVG + DXF Files of all major parts What materials are used? • (1) 48″ x 96″ x 3/4″ Melamine • (1) 24” x 48” x 1/4” MDF • (1) 24” x 48” x 1/2” MDF • (1) 24” x 48” x 3/4” MDF • (~50) Pin Nails or Finish Nails • (~40) 1 1/4” Powerhead Fast Cap Screws - https://amzn.to/2O2Fnmu (affiliate link) • (~30) Misc small screws • (1) Piano Hinge 24” - https://amzn.to/3f2ygoV (affiliate link) • (1 or 2) 3-1/2” Pulley - This depends on what motor you have and what pulleys you may already have. Size of pulley is beyond the scope of these plans. I used an 1800RPM motor with two 3-1/2” pulleys. https://amzn.to/304vZp7 (affiliate link) • (1) 3/4” x 36” Keyed Shaft - If you can find a shorter one that will work. This was what I could find affordably. https://amzn.to/39wrtmc (affiliate link) • (1) Adjustable V-Belt - https://amzn.to/2X1vtWN (affiliate link) • (1) 3/16” key stock 24” - https://amzn.to/2DdrYWc (affiliate link) • (2) Pillow Block Flange Bearings 3/4” - https://amzn.to/39zL19t (affiliate link) • (1) Power Switch - https://amzn.to/3hC3JQo (affiliate link) • (1) 1/2” Threaded Rod 9” Long - I found this at my local ACE hardware. https://amzn.to/2CSNqA9 (affiliate link) • (1) 1/2” Nut and Wing Nut • (8) 7/16” x 2” Bolts and Nylon Lock Nut • (1) Electric Motor - We used an old 1/2HP Blower motor at 1800RPM. This is a good alternative that’s new. You will likely want a small pulley on the motor to slow the drum speed down. a 2” pulley should be good. https://amzn.to/302Naas (affiliate link) • (1 roll) PVC Edge Banding - Optional. To hide the Melamine edges. https://amzn.to/302KVny (affiliate link) • (1) Wood glue - Titebond 2 is what we used but, any wood glue works. https://amzn.to/3hHDNDb (affiliate link)
Detailed build plans for a DIY 24 inch drum sander. A very simple design and a fast build. There is a full youtube video showing how to do it found here at this link. https://www.youtube.com/watch?v=8BM3f6j-ej8&t=74s
Homemade Drum Sander: We actually made it and it works! A drum sander has been on our need/want list for a very long time and we are thrilled that we DIY'd it! This homemade drum sander is going to help out so much and make sanding less awful. You can watch the video bel…
I’ve decided to build a thickness planer. There are many posted here on the net and I’ve looked at a lot of them. (maybe all, at least all I could find) – -Thank You for all those that posted…
Wondering how to clean sanding belts in your shop? Watch this video that demonstrates how to clean the belts in order to get the most use out of them.
