พืชคือสิ่งที่ธรรมชาติสร้างมาให้เติบโตในดิน เราอยากให้คนกินและคนผลิตได้ฉุกคิดซักนิด จะได้เลือกกินได้ถูกใจ ปลอดภัยกับเราและโลก . . #ผักไฮโดรโปนิกส์...
Anlagenneubegruenung am Fluss
Pagina personala Emil Matei
I've been working on a small mockup to test some ideas for asphalt and street trackage. 📷 (Photos in this post updated by Bill Brillinger from archived images) Original photo: http://i1089.photobucket.com/albums/i347/Steven_A_S/asphalt4_zps3ea3a39b.jpg /> I used 1mm black craft foam on code 100 track. You can go the full width of the rails and not interfere with the flanges, as long as they aren't pizza cutters. The stuff at Michael's is 2mm (Hobby Lobby's is even thicker), which is fine for roads without track, but for street trackage you'll need to order some 1mm. An eBay seller named Wandy-Foam sells it. 📷 Original Image: http://i1089.photobucket.com/albums/i347/Steven_A_S/Asphalt2_zpsa56966a2.png The white foam underneath is Readiboard from the Dollar Tree store. While you're there, get some LA's Awesome spray cleaner. Spray it all over the board, wait a minute, and then peel off the paper layers. Do both sides or it may warp. You'll be left with a foam sheet that's a few millimeters thick. I sanded the white foam to give the road a crown. I also sanded in some dips and ruts, though they don't show up very well in the photos. They need to be exaggerated. The paint is water-based craft paint from Michael's or Walmart. You can buy shades of gray paint, but if you want to mix your own, mixing black with white will result in a blueish tint. I mixed black with a light tan (suede) to remove any tint. I dabbed it on using a damp kitchen sponge. Look for a sponge that doesn't have any sort of pattern embossed into it. I also cut the sponge in half, using one half to apply the paint. The other was kept clean and damp and was used to remove paint if needed, such as the dark areas down the middle of the lanes. You want to dab the sponge on something else first, such as a piece of cardboard, to remove some paint (sort of like dry brushing.) 📷 Original Image: http://i1089.photobucket.com/albums/i347/Steven_A_S/asphalt3_zpsd022e3b8.jpg After the paint is dry, you can create patches and large cracks by tearing the craft foam. If you want fairly straight lines, score the underside of the foam with an X-Acto before tearing it. If you want more irregular lines then don't bother scoring first. To darken the patches I just ran them under the faucet for a minute and rubbed them with my finger to remove paint. Some patches are lighter than the road, so mix up a batch of light gray and dab some onto the patch. For the small cracks I took a straight pin, clipped off the head, and chucked it into my Dremel mototool. I also used the grinding wheel on my Dremel to file a flat spot on the side of the pin point to give it a bit of a cutting edge. Then just etch the cracks into the craft foam. You can control the width of the cracks by how deep the pin penetrates. It helps to have some reference photos when drawing cracks. The street view on Google maps is good for this. You can paint tar lines on some of the cracks with a long thin brush. Use very dark gray instead of black because even tar fades. For the white lines, I didn't want to use decals or chart tape because those would be too perfect for an old worn road. I used masking tape to mask off the lines. I reduced the stickiness of the tape by pressing it to the floor and pulling it up a few times. Even after doing this it took up a little bit of paint which really didn't look that bad. It gave some random wear to the pavement. If you don't want the tape to pull up any paint you should probably seal the foam with clear flat spray paint first. I used the sponge to dab the white paint for the lines. The water in the sponge apparently allowed the paint to bleed a little under the tape making the edges a little messy in spots. I probably should have used a cosmetics sponge for this. Those don't need to be moist to be kept soft. I brushed some real dirt onto road to make it look better. I attached the craft foam to the white foam using spray adhesive. 📷 Original Image: http://i1089.photobucket.com/albums/i347/Steven_A_S/asphalt5_zpsee3f161d.jpg ETA: I should give credit where credit is due. I originally tried a technique described by Dan Crowley where he brushed tinted plaster on top of craft foam. The rigid plaster wasn't suitable for between the rails, and it didn't really allow for cutting out patches, but it got me to experiment with the craft foam. Steve S
Splatoon - Ikasu Acrylic Keychain w/Rubber Charm: Boy (Shooter)
Anlagenneubegruenung
BY BLOG EDITOR LAUREN MAULDIN Barns. They’re a mash of ponies and personalities, and are best when they exist as a warm place of community where riders practice their equitation and listen to their horses happily crunching carrots. But if you think peaceful sounds boring, then you might be able to become a barn favorite. […]
Nuts & Volts Magazine is written for the hands-on electronics hobbyist, design engineer, technician, and experimenter.
Dein Pferd geht nicht gut vorwärts? Du kannst nicht locker mitschwingen? Scheinbar ganz unterschiedliche Probleme, die ihre Ursache an der selben Stelle haben können: Den Oberschenkeln.
Danke, Henk. Verladung beim Güterbahnhof: 50 591 mit ein gemischter Güterzug kommt an Schwarzburg vorbei: Das Aussicht üb
Old signs for your layout
São dois circuitos super simples, sem componentes especiais e que tem um bom desempenho, mas um curto alcance. Ele está configurado para a frequência de 433MHZ,
Nuts & Volts Magazine is written for the hands-on electronics hobbyist, design engineer, technician, and experimenter.
Tekenen leren online want tekenen is een hobby die veel voldoening en waardering kan geven. Het is meestal een kwestie van op de juiste
First off, I normally do not refer to myself in the third person as the subject of this post may imply. I was made aware that there was a long thread on the subject of my layout being better because it is smaller by ano…
Before anything, I'll briefly explain what 18650 cells are and what uses they may have. I have worked a lot with 18650 cells and I used them for pretty much anything that needs power. Basically, they are Li-Ion cells, that means they have the same overall parameters as a now-days phone battery. Their nominal voltage…
If you want control the DVD or TV/AV system that located in your living room via the remote control when you sleeping in your Bedroom. this IR extender will achieve this for you. Basically, it works as a repeater that moves the IR signal to a different location. This is an improved IR remote control extender circuit. It has high noise immunity, is resistant to ambient and reflected light and has an increased range from remote control to the extender circuit of about 7 meters. It should work with any domestic apparatus that use 36-38kHz for the IR carrier frequency.