Ken's storm windows: 1. Materials Needed: Standard 1/2" pipe insulation (cost ~$1 for 6'); 2 pieces the length of the window and 2 pieces the width of the window 1"x2" lumber (we found some cull that was very cheap!); 2 pieces the length of the window and 2 pieces the width of the window 1"x1" lumber for cross bar (does not need to be 1x1; any scrap 1xsomething will work. You'll need a piece a bit smaller than the window's width) Wood glue Four 5/8" (no. 6) wood screws Heavy duty staple gun or brad nailer & staples or nails (>1/2") Heat-shrink window film (twice as large as the window you're covering, for both sides of storm) Double-sided tape that comes with window film Small strap (scrap of ribbon or thin nylon webbing) Trusty hammer & screwdriver Scissors Hair dryer 2. Build the frame Cut 1"x2" to length (length or width of window opening minus 3/4" for foam. We recommend you test out the measurements on your window/with your foam before cutting all your lumber). We wanted the storms to push in between the stops, so they'd keep out cold air from the sash pockets, so we measured between the stops. Make lap joints (cut half way through end of boards the same distance from the end as the width of the board creating a large rabbet). We used a table saw, with the blade set to half the height of a board (3/8"). Clamp on a fence the width of a board, then run the board across the blade several times to remove the material. Repeat with all 4 boards for each window. Glue the joints, making sure to cover all sides that touch. Hold the joints at right angles, with a square, and staple, or brad nail, the joints. Complete the four-sided frame and put one screw in each joint - the staples or nails are just pinning the thing together and it needs a screw to be structurally stable. You could also just use a few screws; we thought the stapling worked great & was quick. Note: we did not stain or paint the wood. Very little of the wood shows when installed, they're only in for the winter, and we weren't sure how well the tape would stick to a finished surface. 3. Add the cross-bar Dry fit the 1"x1" cross bar in the frame at the same height as the sash interface and mark. This cross-bar should be the length of the window's width, minus 2 widths of your 1x2 stock. We found that without the cross-bar, the storm windows bowed in a bit when installed. Pilot drill for a single finish nail (6d, 2"), glue the ends of the cross bar and nail together. Doing several windows at once really saves time. Especially if you have the jig all set up for the table saw. 4. Tape the perimeter Add tape to wood frame, near the middle of the board. Press down hard. Peel the backer to expose the adhesive. 5. Lay plastic Find a friend to help. Lay plastic over taped side. Do not pull too tight but cover the whole frame so it's fairly taut. Press plastic film into adhesive tape with finger. Trim off excess plastic. Note: a utility knife sucks for this - for some reason, the plastic is really linear and won't cut right. Instead, run sharp scissors along the edge of the frame. Much better. 6. Shrink plastic Heat plastic film with dryer untill all wrinkles are gone. Press film into adhesive tape while heating the film. Flip the frame over; repeat steps 5 and 6 for the other side of the frame, creating a sealed pocket of air. 7. Add pull-tabs Staple a scrap of folded ribbon to the back and up over the top - so when pulled the ribbon is attached to the back of the joint. This is so you have a way to get the windows out in the spring! They install tightly. We put two tabs on the top of each window. If you're picky (like Sarah), make sure the scrap ribbons coordinate with the paint color of the room. At this point, you could label the window with its room and placement so you'll remember next year! We are labeling them along the top, near one of the ribbon tabs. 8. Add foam gasket Carefully split open the seam in foam insulation. Cut foam to length with 45 degree angle. Stretch foam over edge of frame and match corners of foam edges. Trim if necessary. 9. Install! (a.k.a., smush into window opening) Press into window opening, one side at a time. May require some force, keep foam aligned. We ended up with at least half of our lumber from the cull pile, some scraps we already had in the shop, and most of the plastic purchased new ($11 for a box with 9 big sheets). Ribbons were free from the scrap drawer. Foam was $0.98/piece for a 6 ft section (there were 3' sections in a 4-pack bag that were a bit cheaper for some of the small ends). Overall, we estimate that this project cost about $7 average per window, and we're doing 31 windows (over half are done, rest are started!) The dark foam makes them fade into the window and they're not real noticeable. They seem to work great so far.