Are you considering a ceiling texture for your home? We've got the best types of textures with instructions on how to DIY, tools, materials, pros and cons.
Sorry, there's really no pun to explain a ceiling texture tutorial. After the drywall was finished, it was time to mud. Mike's the drywall extraordinaire, so I let him do his thing. Plus mudding falls into that category of "messy things that don't easily wash out of clothing", so it's better that I don't watch. After everything was mudded I was called down again to help with ceiling texture. Since we tore out all the ceilings on the second floor, and just recently did the ceiling in the new bathroom, we knew what we were doing, and most importantly who's good at what. Mike's the roller and I'm the stamper. Since I didn't explain how we did it for either of those projects, I figured now's as good a time as any to make a tutorial. First, you have to decide what type of texture you want. This isn't the most important design decision you have to make, but have you ever looked up in a room and saw a popcorn ceiling and cringed? Yeah, don't be those people. We prefer a knockdown look, because it's simple and more modern, which is basically adding a stamped textured, then coming back and, you guessed it, knocking it down with a squeegee, don't worry pictures are coming. First, you want to gather your supplies, 1. Joint Compound | 2. Roller, (the thicker the nap, the more texture) | 3. Rubber Squeegee Knockdown Knife | 4. Oval Single Texture Brush After gathering your supplies, you need to prep the ceilings. Since Mike already mudded all the joints, he roughly sanded everything to a smooth finish. Since you're covering it up with a texture it doesn't have to be perfect, but you don't want any noticeable edges that may show through. You should probably not be a dumbass and wear safety glasses during this. Nobody likes extra fine joint compound dust in their eyes. Heck, you should probably wear a full mask, even if you are just taking pictures, that stuff gets everywhere. Next, quickly wipe down the ceilings to throw even more compound dust in the air to fall and get everything dirty. We've cleaned this room probably 5 times already, but, I'm not bitter. Now comes the real stuff. We use premixed joint compound, so Mike just slaps some into an empty bucket and adds a little bit of water to thin it out. The point of thinning it is so it easily rolls onto the ceiling. TIP: Buy one of the those rounded trowels you see Mike holding. It's made specifically for scraping buckets. After you add the right amount of water, (Mike's done this a few times to he knows how much to add, but for someone doing it for the first time I'd add a little bit at a time, maybe a cup or two each time for a half of a 5-gallon bucket), you use a drill attachment to mix it up. The consistency is thinner than peanut butter, more like brownie batter. You know, easy enough to pour, but you still need a spatula to spread it all out. Definitely thicker than paint, even the really thick primer stuff. Then you use a roller attached to a long pole to dip into the mixture and coat really well. After the roller is thoroughly loaded up, start rolling onto the ceiling. Mike likes to work in square sections, making sure the area is evenly coated. We only had a smaller nap roller on hand so Mike went over the area a couple times to coat it. You're looking for a thin, even, layer, about 3/8" thick. The thinner or thicker you coat it, the lighter or heavier the texture is going to be. While Mike was rolling, I was mentally preparing myself for the very important task of texturing. Actually, it requires little thought at all and is pretty fun, (my kind of tasks). I waited for Mike to finish the whole length and about a 4 foot section before I got to work. It's important to have one person do the textureing, because once you find your groove, it's going to be unique and adding someone else, will yield a different style. That's why I like to say I have the most important part of the job, although I usually don't say it out loud. Don't want to bring down the morale of my partner. So, I'm up and I use the brush and firmly stamp it in the wet compound keeping the brush flat. The roller leaves the veiny looking texture behind, but you're looking for the stippled effect. The oval brush leaves an oval negative space in the middle, so as you stamp, you need to rotate the brush so everything has a uniform texture. By the time I'm done stamping my section, Mike's done with another 4' section, so we move down the room together. Make sure to get all the ceiling, including the edges, it may get on the walls, but it's worth it. Depending on the size of the room, (and how long it takes you to roll and stamp), the next step may require some waiting time. Since the room is pretty big and Mike took his time rolling on the compound, (due to the smaller nap), we only waited a couple minutes before starting at the beginning of the room to do the knockdown. The knockdown technique takes some practice. Mike's got it down, but I wouldn't attempt it without practice on a piece of cardboard or something. The compound needs to be stiff, but not completely dry. The squeegee is used to flatten the pointy edges of the stamp, but you don't want to wipe everything off by doing it too early. Mike usually uses his finger to test a spot to see if it's dry enough. If it sticks to your fingers it's too wet, it needs to come off somewhat clean, but have a little resistance when you touch it. Make sure the squeegee is clean, and holding it at a 45 degree angle, lightly wipe across the ceiling. As you can see in the picture below, there's a small sliver of light between the squeegee and ceiling. There's not a lot of pressure used, you're just skimming the very top to flatten those points. Mike does one pass at a time, about 4' in length, to maintain control. He cleans the squeegee off with a clean towel ofter every pass. This part takes some patience, but goes really quickly. You don't want to be too long, because the other side of the room is drying while you're working. If the compound dries completely, (which you would have to be really slow for that to happen - it's usually too wet and requires waiting), it won't work, and you'll have to sand it to get the same texture. After the room is rolled, stamped, and knocked down, Mike takes a flat edges trowel and scrapes along the edges of the ceiling to get all of the compound off of the wall. It's easiest with a trowel because you can start with the trowel up in the corner and scrape down, making sure that all that hard earned texture remains. I know this post is getting lengthy, but I also wanted to share how to retexture a ceiling since many may not be installing new ceilings all the time. We kept the ceilings in the stairwell, but had cut holes for wiring and lights so we wanted to add new texture. We also wanted it to match the new ceiling down the stairs more so than the stipple texture that was already there. For most, the knowdown look can be achieved with simply sanding all the pointy edges down. But like we had, there may be holes that needed to be filled, so we textured over everything. The only difference between new texture and retexturing, is the thickness. You want to first sand down all the point edges, (if you have popcorn ceilings, first let me me say I'm sorry, but that also means you can completely remove the popcorn and start over as if it was new), this is only necessary if you have a texture like the rosebud: via After sanding all the points down, you want to follow the same steps above, but apply a much thicker layer of compound. A thicker nap roller will definitely come in handy for this. Then you will have to stamp a little bit lighter since you have a thicker layer. And, then wait a little bit longer for it to set up before knocking it down. We did it in the steps first and the only difference was the space was a little tighter. We kept it a little lighter in the steps than what I suggested for retexturing because after sanding down the original ceilings, it was pretty much the look we were going for. The point of redoing it all was to blend the patched holes. After letting it dry overnight I was able primer and paint everything over the next couple of days. Since I've bored everyone to tears with such a detailed tutorial on ceiling texture I'll leave you with a look at the lights we were able to install after the paint was dried. These bad boys are amazing and have made such a difference in the room already. It's made the late nights working down here almost tolerable. Or at least tricked us into thinking it's not as late as it really is with all the light.
The thing about big long home renovation projects is that they defy the space-time continuum. How could skim coating a ceiling take most of a week?
From simple comb texture grooves to intricate floral texture designs, discover 13 ceiling textures to improve the look of the home.
I promised that I'd show you pics of the bedroom now that it's painted, but before I can do that I have to share how we added texture to the newly drywalled ceiling for the cost of a bucket of mud ($10). It's so much easier than I thought it would be! This needs to be done before painting the walls. Step 1: Take regular drywall mud, add it to another bucket (we used an empty drywall bucket), and add water until it's about the consistency of brownie batter. We used the drill with the following attachment to mix. See a similar mixer here Step 2: Pour it into a paint pan, take a regular paint roller, and start rolling it on the ceiling. The ceiling does not need to be primed. Just sand down the joints and clean it up. Step 3: Follow immediately with a texture brush. My husband rolled and I followed with the brush. Basically you just do a stamping motion on the ceiling. Bedroom ceiling before We are putting crown molding up in this room. That's why the corners aren't taped and mudded. If you're not using crown molding, tap and mud corners before adding texture to the ceiling. Rolling it on Followed by stamping. This is the brush we used. We borrowed it. (Thanks, Jeremy!) Step 4: Let it dry overnight. Touch up, if need be, the next day. Here are the after pictures: Sorry, I had a heck of a time getting a decent picture of the whole ceiling. Easy peasy, right?
We're in week 4 of the One Room Challenge and entering the homestretch. For today's post we're sharing the easy way to create knockdown ceiling texture.
Is your flat ceiling looking a little plain? Adding texture to your ceiling is an easy way to jazz up the room and make it look a little more decorative. Plus, a nice texture on the ceiling is a great way to cover up imperfections in the...
Not sure how to paint your ceilings. Here's the complete guide on the benefits of a textured ceiling vs. a smooth ceiling.
A DIY tutorial for how to remove popcorn ceiling (or "stomped" ceiling, or other texture)
I promised that I'd show you pics of the bedroom now that it's painted, but before I can do that I have to share how we added texture to...
How to skim coat & smooth a textured wall, drywall or ceiling! Easy DIY home improvement & remodel project. Detailed tutorial, video & best beginner tips!
Gallery of ceiling texture types including popular pattern design ideas. Find out what ceiling texture is best for your home style.
Often removing a popcorn ceiling becomes part of a ceiling repair.It is a very messy job but many home owners feel it is worth the expense in time and/or
Do you have heavily textured or popcorn ceilings you want to cover? In this guide, we will outline how to cover popcorn ceiling and the cheapest way to do it. No scraping is required!
There are many ways to cover an unsightly ceiling—here are 11 ceiling coverup ideas to consider.
I never knew how easy it was to patch and texture ceiling drywall. Check out how we easily fixed the hole in our master bathroom ceiling during our remodel.
How to remove a textured ceiling. Stippled ceiling to smooth ceiling.
Need to learn how to paint a ceiling? Let me teach you how to do it the easy way! Use these tips and tricks to save yourself time and keep you from making a huge mess.
Textured ceilings are in and out of style regularly. Although many people give little or no consideration to ceiling finishes, texturing a ceiling usually
Want to add a beadboard ceiling to a room in your home? Here's everything you need to know about how to install beadboard ceiling panels!
Our specific variety of textured ceiling has a few names: crows feet, stomp texture, slap brush, and panda paw. Don't those all sound exciting and fun? THEY'RE NOT!!! We have ceilings like this all over our home. The texture is so dimensional that we jokingly call them stalactites. Mostly I hate them because they collect dust and create shadows on the ceiling. See how dark the ceiling looks in that first photo? Everyone we talked to said they're very hard to remove completely (they're applied differently than popcorn), and thus it's quite expensive to have it done. We don't hate them enough to throw thousands of dollars into making them disappear, so we thought we'd try something cheaper first. How about just sanding them a little? Armed with lots of protective gear (glasses and mask are a must!), we just wrapped sand paper around a sanding block and went at it. The stalactites broke off easily, and the smaller mountains sanded down without too much more elbow grease. It took a little over an hour to do this 10' x 9' room in our house. Cleanup was another half an hour, because this process creates a LOT of dust (be sure to open the windows, close the vents, and shut off the AC). This project was super cheap - just the cost of a pack of sandpaper. Here's a closeup of what it's like after sanding. It's not totally smooth (that costs big bucks), but it's a huge improvement! Here's the room half finished. The left side has been sanded already. Doesn't the ceiling look so much better? Cleaner, brighter, more welcoming. Such a difference! Let's compare to the "before" again: Now I have the itch to do the rest of the house... Be careful, because it will make quite a mess! Bonnie Projects
Give your plain, uninspired walls new life with these timeless wall texture types. Check out this guide for inspiration and tips.
