There's something about a fireplace that just makes a home feel more cozy! I love that we have a large fireplace in the center of our home. I wrapped it in shiplap to make it

This Floating Beam Mantel was the beautiful final touch on the Roman Clay Fireplace I modernized for my brother. Easy beginner tutorial!

I have SUCH an exciting and highly-requested tutorial for you today, sweet friends! Ever since I found the faux mantel that now lives in my bedroom, so many of you have asked where you might be able to find something similar. The mantel I bought was handmade and a very simple design, so I knew…

I have always wanted a fireplace and now I can say I have one! Well, a faux one. But that works for me. And I got it done just in time to start decorating for Christmas. 🙌🏼 I also have a place to hang out stockings now! Side note, these are my FAVORITE stockings made by my sweet friend Rendi from @thevintagebucket CLICK HERE for more details on them! I provided a list of the wood I purchased before the cuts and then a breakdown of the wood cuts you’ll need. Sometimes wood cuts can be overwhelming when you have a ton of them for a tutorial, so I am hoping this will lessen the confusion. Ok, let’s talk materials! Wood: (before cuts) 2 – 1 x 7 x 8’ 1 – 1 x 10 x 8’ 1 – 2 x 10 x 10’ 1 – 1 x 4 x 8’ 1 – 1 x 12 x 4’ 1 – 2 x 4 x 8’ Tip: I can only fit boards that are 8’ long or shorter in my SUV, so I had an associate at Lowe’s cut the 2x10x10 to 2 – 53”. You will probably need to do this unless you have a truck. 🤗 Bonus, this takes care of your mantle and base cuts. Wood Cuts: 2 – 1 x 7 x 44” – outside fireplace pieces 2 – 1 x 10 x 44” – outside fireplace pieces 2 – 1 x 7 x 32 3/4” – inside fireplace pieces 2 – 2 x 10 x 53” – mantle and base 2 – 1 x 4 x 31” – front trim 2 – 1 x 4 x 6 2/16” – front trim end pieces 1 – 1 x 12 x 4’ – center piece below mantle 1 – 2 x 4 x 4’ – inside support piece for mantle Tools & Materials: Miter saw Hammer Electric screwdriver Tape measure Level Kreg Jig Clamp 1 1/4” pocket hole screws 1 1/2” wood screws 2” wood screws 1 1/2” finishing nails Wood filler Orbital sander 120 grit sandpaper Paint brush Paint Note: For the paint I used SW Snowbound to match the trim. Step 1: Cut all the wood. Step 2: Using a Kreg, drill 5 pocket holes down one side of the 1 x 7 x 44” piece. Repeat on the other 1 x 7 x 44” piece. Step 3: Align one of the 1 x 7 x 44” pieces on top of one of the 1 x 10 x 44” pieces (the 7′ wide board should butt up against the end of the 10″ wide board) and secure them together with 1 1/4” pocket hole screws. Repeat on the other side. These pieces are the ends of the fireplace. See below for reference. Step 4: Lay the end pieces parallel to each other (with the 10” boards facedown) on a flat surface then place the 1 x 12 x 4’ along the top edge of the ends. The ends of the 12” board should butt up against the top and ends of the 1 x 10 x 44” pieces. See picture below. Step 5: Using 8 – 1 1/2” wood screws (4 on each side) secure the 12” board to the backs of the 10” boards. See above picture. Note: The opening of the fireplace should measure 31” from end-to-end. Step 6: Using a Kreg, drill 4 pocket holes down one side of the 1 x 7 x 32 3/4” piece. Repeat on the other 1 x 7 x 32 3/4” piece. Step 7: Secure the 1 x 7 x 32 3/4” pieces on the other ends of the front facing 10” boards using 1 1/4” pocket hole screws. These are the inside pieces of the fireplace. Once secure the center should look boxed in. I will refer to this as “the box” moving forward. Step 8: Lay the box facedown and align the 2 x 4 x 4’ along the back edge of the box, then secure it to inside of the box with 2-2” screws on each side. The screws will be on the outside of the box. I just painted over the screws, but you can use wood filler to hide them before painting if desired. See below. Note: As you can see I did not complete the steps in the order I am showing you. Mainly because I was building from scratch and had to adjust the frame several times. The order I am sharing with you is the most efficient way to build the fireplace. Step 9: Place the mantle (one of the 2 x 10 x 53” pieces) on a flat surface then place the box upside down on top of it, centered. You want to make sure the 2 x 4 x 4’ piece is aligned with the back edge of the mantle. Then secure the box to the mantle by using 5 – 2” screws. The hangover of the mantle should be on the front side of the fireplace. Step 10: (optional) secure the trim (2 – 1 x 4 x 31” pieces and 2 – 1 x 4 x 6 2/16” pieces) around the front center piece of the fireplace using 1 1/2” finishing nails. See picture below. Step 11: Secure the base. With the box upside down, center the base to the box with the back edge of the base aligned with the back edge of the box (the overhang should be in the front just as it is with the mantle) then use 2” wood screws to secure the base to the box. Step 12: Use wood filler to fill in the holes from the outside screws or just paint over them. If you use wood filler, allow the wood filler to dry completely. Then sand the fireplace to a smooth finish using 120 grit sandpaper. Step 13: Paint the fireplace. I used SW Snowbound paint to match the trim. I applied two coats of paint, then let it dry overnight before decorating. Step 14: Decorate your new faux fireplace! I bought corbels to add to the front, but not sure if I’m going to add them. They are a bit smaller than I thought they would be. So until I can figure out how I am going to incorporate the corbels, the fireplace will be left like this, which I am completely ok with. If you want to know how to make the garland CLICK HERE. Also, if you are wondering what the wall color is, it’s SW Evergreens. Doesn’t it look so pretty with the Christmas decor? I might keep this up year round. Just kidding, but I do love it! And that’s a wrap! I hope you enjoyed my tutorial and find it inspiring to build your own. It’s definitely not the real thing, but I love it just as much. 😍 If you have any questions please comment below. If you use my plans to build your own, I would love to know about it! You can tag me on Instagram. My handle is @acarriedaffairdesigns Until next time. Xo

Камин из гипсокартона своими руками: пошаговый алгоритм работ

Want to remodel your home, so it flows from room to room? See how these Portland homeowners remodeled their 1995 builder-grade home.

It all begins with an idea.

Lacking a mantle for your fireplace? I’m sharing a DIY tutorial for creating a mantle using simple and affordable materials. I shared our recent fireplace makeover earlier this week, and now I’m going to give the promised tutorial for our DIY mantel. These things were so easy to make, and I think they were just the...

This residence welcomes with its light-filled, spacious rooms. Located in Avalon, New Jersey, it showcases the warmth that reclaimed materials lend to ultra-modern shore homes. Wood worn to sandy tones plays against crisp shiplap and marble to create an instant sense of history.

Are you looking for some amazing Christmas mantel decor ideas try out this year? If so, you’ve come to the right post! Christmas is right around the corner, which means …

Making a popcorn garland is inexpensive, beautiful, and super easy to do! Their timeless charm just adds such a cozy feel to your home...