Pattern: Self drafted body. Sleeves taken from Waugh's Cut of Women's Clothes. Fabric: 100% cotton twill, rich green, with a very soft hand (feels almost like a low pile velvet!). The petticoat is 100% silk taffeta of varying stripes in golds, greens, and browns. Measurements: Chest: 38-39" Waist: 32-33" Back Width (garment, between armhole seams): 12" Back Width (body, between arm sockets): 14" Back Length, garment (from top to natural waist): 12.25" Back Length, body (nap of neck to natural waist): 16.25 Shoulders: 16.5" Torso length, side (from underarm seam to bottom): 8.25" Front Length: 13" Bicep: 13" max Sleeve Length (inside curve): 18.5" Sleeve Length (outside curve): 26" Hem: 39" at front, 42" at back. Summary: A new drafting for a simple, late 1780s Pierrot jacket. The sleeves are full length with eyelets on the cuff, laced shut with ribbon. The body has only two pattern pieces, front and back. The back pieces are quite narrow to lend the optical illusion of a narrow back. I did this version in a soft cotton twill, single face. The surface is very soft, almost like a low pile cotton velvet. The jacket is fully lined in gold/tan silk. The center front closure is done is pins (in the pictures, the pins are placed horizontally to the body, making them practically invisible) *See the bottom of the post for more completion photos Construction The entire jacket has 5 pattern pieces: Front Back Shoulder Strap Upper Sleeve Under Sleeve As such, construction is pretty straight forward depending on the technique you wish you to use when setting in the sleeves. I chose the rather more complicated "sandwich" method of setting in the sleeves. I'm not sure if there is already an established term or phrase for this 18th century (and possibly earlier?) method of setting in sleeves. It involves fitting the top of the sleeve over the shoulder lining piece, wrong sides together, and then top-stitching the outer shoulder strap over everything to finish. The result is that the seam allowance of the top of the sleeve is "sandwiched" between the lining and outer pieces of the shoulder strap. Here you see the body of the jacket basically finished with only the shoulder strap left off. The shoulder strap lining has the neck edge seam allowance already pressed under. (Below) The sleeves are attached around the bottom curve, leaving the shoulder strap area free. This is a step that can be done on machine, if desired. NOTE: For this step, you are attaching only the fashion fabric of the sleeve, not the lining. The lining is pushed down into the sleeve away, to be attached to the armhole seam later. (Below) The process of fitting the sleeve over the round of the shoulder and onto the strap lining is--I'll be honest--a royal pain. Don't waist time trying to be precise with mathematically even pleats. Just eyeball it. Because dress forms don't have arms, you have to be careful that you don't set the sleeve in too far and end up not leaving enough "rounded" area for he shoulder that will eventually be in there. [I recommend making detachable arms, or shoulder shoulder arounds, that you can attach to your dress form for this reason] Pinning on a form can be tricky because your pins might go too deep and attach to the form itself. I avoid this by using a piece of flexible plastic, roughly 7" long, maybe 2-3" wide, that I can slip in under the garment where I'm pinning and keep them from reaching the form. The tiny bit of blue you see poking out in the top photo is the plastic piece. Now the frustrating part lol. As you can see, the sheer number of pins necessary to keep everything in it's place for the hand top stitching means that you will probably want to avoid tight woven silks like taffeta and other fabrics that show pin holes badly. Lucky this cotton twill doesn't show pin holes at all, so I could go crazy. Top stitching down the shoulders straps MUST be done by hand. You could finagle all of this under the presser foot of a sewing machine, but why would you want to? Machine top stitching would be far too noticeable and defeat the purpose of using a period accurate setting technique to begin with. Lining I chose to assemble the body lining separately and then set it in around all outer edges with edge stitching (all done by hand). I did this for two reasons: 1) I really like the look of hand edge stitching. It's that extra bit of authenticity, and 2) Edge stitching creates a permanent clean pressed edge around the garment, so even after cleaning you won't be frustrated trying to iron the edge of your garment to keep the lining from peaking out, etc. The lining for the sleeves I chose to slip stitch in by hand. I'm really not a fan of exposed seams, so I lean toward construction techniques that "bind" everything in. (Above) The sleeves lining top, with seam allowance turned under, and pinned in place for slip stitching. The top curve of the lining is gathered into place rather than pleated. (Below) The inside armhole, with lining finished. Cuffs & Peplum The tail, or peplum, of the jacket is trimmed with a 1.25" wide ruffle of the same green twill, trimmed on three edges with a narrow vintage cotton lace. The lace is not 18th century, of course, but is likely from the late 19th century. I got it from an antique blouse I found at an antique mart that was otherwise too far gone to be salvaged. All the work on the peplum trim is done by hand. The cuffs are attached to the sleeves separately, with hand whip-stitching to the lining inside, allowing them to be removed easily if desired. The cuffs are also vintage pieces, taken from an Edwardian child's dress that was too damaged to keep intact. The lace is attached to the cotton organdy base by hand, and gathered and stitched to the lining edge inside the sleeve. FINISHED