TABLE The beauty of making your own table is that you can make the table top any size you want/need and you can make it the height you want. Dining room tables are usually 29 – 30” high, a sofa table could be 36” high and end tables are 21 – 24” high. And you can use a variety of supplies to keep your costs down. Your basic pieces are: The table top The legs The apron An apron is a wooden panel that connects the surface and legs of a table. It is placed at right angles to the underside of a tabletop, and extends between the top of the legs. The table top can be made of either mat board or 1/16, 3/32, or 1/8” basswood. The apron can be made from those or from coffee stir sticks or craft (popsicle sticks) The legs can be made from square food picks from the Dollar Store (mine are about 3/32 square), 1/8 or ¼” square strip wood, or Houseworks stair balusters #7025 or #7202 on page 14 of the Houseworks catalogue http://houseworksltd.com/pdf/HWKcatalog18spreads.pdf The important thing is that they have square tops. Houseworks also sells table legs (top of page 15) but they only come in packs of 4 whereas the balusters come in packs of 12. In my experience the balusters are more readily available at most miniature shops. From left to right: square food pick, 1/8" strip wood, 1/4" strip wood, Houseworks baluster #7025 Supplies: Metal ruler Fine pencil Utility knife with fresh blade Gluing jig or Lego blocks Wood glue or Weldbond Toothpicks Cutting mat Stain or paint Optional (nice to have but not necessary): Mitre box and saw Easy cutter As an example, here’s a hall table I made using 3/32” basswood for the table top, popsicle sticks for the apron and Houseworks #7025 for the legs. Making the Table Cut your table top to the size you want. This one is 4” x 1 ½”. On the bottom side of the table top, mark in ¼” around the edge of the table top. (For a small table such as an end table, I’d mark in only 1/8” from the edge.) If you’re using the picks or stripwood, cut four pieces to the length needed for the height of the table. Since I used the balusters, I could skip this part. Hold two of the table legs together and place as shown against the pencil line then measure to the opposite pencil line to get the length of your table apron. (This is easier and more accurate than placing a leg on either side and measuring between them.) Cut the two aprons for the length of the table. Use the same method to cut the aprons for the width of the table. If you’re going to stain rather than paint the table, now is the time to do it. You can paint over glue, but you can’t stain over it. Do not stain the tops of your table legs or the ends and one long edge of the apron pieces. (If you do stain them, it's not a big deal but these are the edges that will be glued to the table top and legs and that works a bit better if the glue is applied to the bare wood.) In your gluing jig, glue the ends of the long apron pieces to the tops of your table legs. My gluing jig is large enough that I was able to do both sets of legs at the same time simply by using a couple Lego blocks between each set. When that glue has dried, put one of the sets of legs against one side of the gluing jig. (I hit it lucky here as the distance between the two sets is exactly the width of a piece of Lego!) Glue one end of the short apron pieces to those legs and use the Lego to keep it straight and square. Then glue the other end and attach the second set of legs. (I actually used my upside down mitre box to hold everything in place while the glue dried. OOPS! Forgot to take a picture of what the apron and legs will look like when finished. (This is of the quilt shop table base but you can see the basic construction.) Note that the apron goes on the inside portion of the legs. When the base of the table was solid, I turned it right side up and spread wood glue on all the upper edges. Then I turned it upside down and glued it in place on the bottom of the table. (My original pencil lines were just visible through the stain to help with placement. The completed table! I'll have the tutorial available as a .pdf file later today. If you'd like a copy, email me and I'll send it to you. Please put "table tutorial" in the subject line. My next post will include some variations that I tried.