"Woodland Realm" Silk String Bundle from Marsha Neal Studio Ribbon and leather cording is all the rage, and many of you are probably contemplating adding it to your jewelry repertoire. Finishing off the ends can be a bit of a head-scratcher when you first start out though, especially if you haven't had time to explore all the products and techniques available for attaching your cording sections to the rest of your piece. The first piece I ever sold on Etsy had 2mm Greek leather on it, and I faked up some coil ends on it--I had bought some simple, cheapie ones at the craft store and was trying to copy them. The only think I could think to do was wrap the wire around the ends of the leather and make a loop at the end, but it was really frustrating because the leather was kind of floppy. Ca. March 2005 It was so frustrating in fact, that I didn't use leather in my designs again for a couple years. Later I discovered commercial crimp ends for sale, and used those on a few pieces. From Cool Tools PMC supply They look really nice, and come in different finishes, but in my experience they have a tendency to break. The center section on some styles actually breaks away from the end sections when it's crimped, and this can give way under too much wear, like with a bracelet that gets tugged and twisted a lot when you're trying to put it on or take it off. (I actually had to repair a bracelet where the crimp end broke--I redid it with a different technique.) Could be I squeezed it too much; it's hard to tell how tightly to crimp it. I don't think there are the same issues using these findings with a necklace though, because they don't get the same wear and tear, and I've used them with necklaces without any reported problems so far. With silver plated pewter crimp ends from Fusion Beads I still really wanted to use leather in my bracelets, without having to fold it over a ring or something (because that can be kind of bulky, especially with Greek leather), but I needed something sturdy. It eventually occurred to me (probably in the shower) that I should make the coil and loop BEFORE attaching it to the cording, and THEN slide it onto the leather and tighten it, instead of trying to wrap the wire around the cording. (I have no doubt thousands of jewelry makers have been doing this forever, and I could have learned this from one of them, but perversely self-sufficient freak that I am, I had to take two years to figure it out myself.) So I gave it a shot and it worked fine. This is how I eventually ended up making them--these are in a few different sizes: They look like this when they're attached and tightened up: I like to use 16 gauge wire, as I prefer a chunky, substantial look (and I'm a little paranoid about things coming apart--I also add some adhesive, like GS Hypo Cement or PlioBond--Hypo Cement is clear so probably a little easier to use, PlioBond is more amber colored), and this gauge seems to work for most of what I do. The 16 gauge is not so heavy that it's hard to work with, and I can get the coils down to about 4mm inner diameter, which is the lower limit for most of what I do. If you wanted to do something with just, say, one strand of 2mm Greek leather, you could go down to 18 gauge and get a smaller coil that would still be sturdy enough. (You can always anneal too, if your hands are worn out and need a little extra help--some days the elbow grease just isn't there!) For a 5mm (inner diameter) coil, I use the base of my round nose pliers. Leaving the wire on the spool (you won't cut it until you're totally done), make a coil with three or four courses around. When you actually tighten it up around your cording the whole thing is going to get skinnier and longer and you'll end up with a couple extra courses around. (The longer the finished coil is, the greater the surface area you will have grabbing onto your cording and the more secure it will be.) When you've got your coil completed, you'll need to bend the free end of the wire up to create the loop. I pull up on the free end a bit to create some space for me to slip my bent nose pliers in there: Then I slide the tip of my bent nose pliers under there, and bend it straight up. You can use the pliers as necessary to sharpen the bend a bit. (Again, anneal if you need to--the process of tightening it later will work harden it plenty so it won't open up on you.) Squeeze it together a bit again. After you have your 90 degree angle, it's time to make your loop. I just pop my round nose pliers under there again, near the base, and just bend the wire right over the top. Nip it off with your flush cutters just about even with the top rim. Tuck the end just inside the edge of the coil, and hammer it a bit to strengthen it and give it a finished look. (Hammering is optional, I just like to hammer things.) You might have to trim your loop a bit after hammering it, because that tends to make it a little longer. Once you have a feel for that you can trim it a little shorter right off the bat, so that hammering it will make it just the right length. Make sure the loop goes straight over the top, transecting the coil right across the middle. Adjust as necessary with your pliers. Of course, you can make these any size you like. I just eyeball the cording I'm using and guesstimate what inner diameter I need. It's totally fudge-able because you're going to squeeze it down tight anyway. That said, it's nice to get it as close to the right diameter as possible, because squeezing an oversized coil down is a pain in the butt. You can do it, but it's a lot more work, and of course the more you squeeze it, the tougher the wire gets and once your cording is in there you can't re-anneal. Next time, we'll talk about actually putting it on your cording.