So when my daughter mentioned she wanted to be be Anna for Halloween, I was thrilled at the thought of trying to recreate Ann'a Coronation look. When I watched Frozen, I fell in love with Anna's dress. I loved the way it moved and I loved that it wasn't a traditional frilly princess dress. Making it was very time intensive, but not difficult at all. The little one LOVES it and wants to wear it all day, erry day. And so do I honestly. I may just have to make one for myself next. ; ) I'll run through a quick and dirty how to. If you have questions let me know. This is roughly how I tackled creating this dress. I opted to use fabric with wonder-under on it for all the designs on the bodice and skirt. It took SO. MUCH. TIME. to draw and cut out. But, I don't have an embroiderer, and I was afraid of using paint, so wonder-under it was. I suggest getting the strongest wonder-under available. There are a few pieces that have come off of my daughters dress. It's not a big deal, I just have to cut and iron on a new piece, but you can avoid that by using a strong wonder-under. Let's start with the bodice shall we? I drafted the pattern using one of my daughters well fitting dresses as a guide. It is fully lined, as I can't stand unfinished edges. : ) The bodice is simply a sleeveless heart shaped top with some added sleeves. For the bodice, I used 1/2 a yard of black cotton velveteen found here. For the gold trim, I made some bias tape from a greenish-gold taffeta found at Joann's. Looking back, I would have done something different for the trim, perhaps some pretty gold ribbon instead. The taffeta was difficult to work with around the rounded front and I wasn't able to get it as smooth as I would have liked. For the back closure, I opted to use buttons. The sleeves I made with a green satin and white lace. I simply cut a rectangle out of the green satin, hemmed one side, and added lace to the other, then I gathered the rectangle where it would attach to the bodice, and sewed it on. The design, as mentioned above was cut out of fabric backed with wonder-under. It was time intensive, but it turned out pretty well. Next up is the skirt. Cupcake Cosplay has a quick snippet of how she constructed the skirt. It was so very helpful. The skirt is a box pleated. It appears to be A-line when stationary, but with the added panels of the box pleating, the skirt is really shaped like circle skirt. You can see that it is a circle skirt when my daughter twirls. I purchased 2 yards of Robert Kauffman kona cotton olive green fabric found here and 1.5 yards white Kona Cotton. For the hunter green fabric, I used a stiff rodeo fabric to give the skirt a bit more body. Constructing the skirt was my favorite part. I took my daughters waist measurement and decided that I wanted 8 panels of the olive green and white. So I took my daughters waist measurement and divided by 8. This should be the finished the width of the top of each panel. waist / 8 = finished width of top of each panel for example 24''/8=3 So the finished width of the top of each of the 8 panels would be 3 inches. I then had to divide the finished width into the different color sections (white and green). I knew that I wanted the olive green to be 2 inches wide at the top to make room for the design. So that left 1/2'' for the two white sections. Then I decided that I wanted the finished width of the bottom of each panel to be 8 inches total, so I divided the bottom into green and white sections. The white sections I decided would be 2 inches wide a the bottom and the green would be 4 inches wide. Now that I had my width measurements, I measured my daughter from waist to feet to get the length of the panels. I drew a trapezoid that looked like this (your measurements will vary depending on your sizing needs): I then cut out what will become the three sections of each panel, and traced it onto another piece of drafting paper with added 1/2'' seam allowances. Clear as mud, right? Email me with questions. Then I could cut out my fabric. I needed 8 of the olive green middle section and 16 of the white side sections. I then sewed all the white side sections to the green sections creating 8 panels that look like the above rendering. Next we will cut out the hunter green panels using the same pattern pieces. You will need 8 total hunter green panels, each panel is divided into three pieces just as you did before. I then sewed the 8 hunter green middle pieces to the 16 hunter green side pieces to create the 8 hunter green panels. Now it is time to sew the hunter green panels to the green and white panels. When you are all done, you should have something that is close to a circle skirt. I did not want to have any hem showing on the skirt, so I created a lining for the skirt that would both hem the skirt and add some weight to the skirt. I used a black sheet and traced and cut out a lining that was the same shape and size as the pieced skirt. I then pinned the black sheet to the bottom of the pieced skirt with right sides together and sewed along the bottom edge. I then turned the fabric right side out and iron the lining up. Next I folded the skirt like a box pleat, with the hunter green folded inside of the olive green panels. After it was folded, I sewed the skirt to the bodice. After all the sewing was done, I ironed the designs onto the skirt. And that is roughly how I created the dress. Clear as mud, right? ; ) If you have questions, don't hesitate to ask. Here are a few close ups, sans ironing. : )