Now you can say it before you even have to say it!! Fun Embroidered Patch "Shit could be worse!" Size 3" Listing is for 1-pc Patch has adhesive on the back and is ready to be sealed with your heat press or iron (without steam) can also be sewn on for added security. Enjoy!! Thanks so much for stopping by! **** How to apply your embroidered patches **** Our embroidered patches can be ironed onto anything you can iron: shirts, jeans, hats, blouses, pants, skirts, etc. Make your clothes and accessories unique! Are you creative? With a heat press or an iron, you can create a new look instantly. It's soooo easy! Heat seal to polyester/cotton fabrics. Do not apply to rainwear (waterproof), highly elastic, rayon, nylon or tri-acetate fabrics. Once applied, applique is permanently attached to the garment and is washable, dryable and dry cleanable. For machine washing, turn garment inside-out before washing and drying. Iron on instructions for embroidered patches using an iron: Step 1: Set your iron at the hottest temperature setting. DO NOT USE STEAM DURING APPLICATION! Step 2: Place embroidered patch in the desired position and place a Teflon sheet on top. Step 3: Press the iron straight down for 35-45 seconds with as much constant pressure as possible. NO BACK AND FORTH. Step 4: Turn the garment inside-out and repeat steps 2 & 3. Step 5: Allow the patch to cool down. Instructions for using a Heat Press: Step 1: Set your heat press to 350 degrees. Step 2: Place your embroidered patch in the desired position and place a Teflon sheet on top. Step 3: Press the garment for 12 seconds. Step 4: Increase temperature to 375 degrees. Turn the garment inside-out and press for 10 more seconds. Step 5: Allow the embroidered patch to cool down.

Details: Approximately sixe: 6x7cm Ready to iron on but also can be stitched on the edges Can be used on denim, canvas, cotton, nonstretchy fabrics (can be used on synthetic fabrics as well, but it might shrink around the edges) Instructions: 1. Preheat the iron ( high heat, no steam) 2. Place the patch with the sticky side down onto the garment. 3. Place a cotton cloth over the patch 4. Iron over patch for 2 minutes at least 5. Remove the cloth and check the patch around the edges. Iron again if necessary 6. Iron inside of the garment, underneath the patch 7. You can also stich the patch around the edges ( not necessary)

4 x 4 inch woven iron on patch

Vintage Celestial Planets Iron On Patch! Our patches are perfect for any pop culture lover! Add them to your jacket, your bag, your cosplay, anywhere you can use an iron! Choose from black or white or buy the pair! The Important Stuff: Dimensions: Approx 18cm x 7cm Backing: Iron On Fabric: Felt Embroidered By: The Craft Rebellion in Brisbane, Australia. The Technical Stuff: Patches can be applied directly to desired garments with an iron. Simply cover with a cloth or parchment paper, Apply firm pressure for 30 seconds on high. Turn garment inside out and repeat. Check bond at edges once cool and if required, repeat process. We recommend a few hand stitches, especially on larger patches to ensure a long-lasting bond and that you only use a gentle hand wash on any felt patches. The Production Stuff: Due to the handmade nature of these items and that we make them to order, our production time can vary from 5 business days to up to 3-4 weeks. This is the time it takes for us to create your patches once you have placed your order. It does not include shipping time. Please check the production timeframe for your items PRIOR to purchase. Please check our store announcement for current processing timeframes. The International Shipping Stuff: Our non tracked international shipping method is no longer available. All international orders are now shipped with DHL and come with tracking and a significantly shorter transit timeframe. **Please note that due to different screen and monitor configurations, colours may vary from those shown in images.

Moth iron on patch. 4 inches wide.

I use to cringe whenever one of my children earned another scout badge. Ug, sewing those tough little things onto a sash was bad enough, but sewing them onto the chest pocket was the worse. Other m…

Patches are special. They can last can travel with you over a lifetime. The Birches patch: * measures 4" x 3" * iron on * or sew on Packaging: * Individually packaged in a plastic sleeve with a hang tag. * Need some ideas on where to put your patch? We got you covered. An insert is included in the packaging that can be viewed in the photos with a list o many ideas. View my other patches here: https://www.etsy.com/shop/ThinkGreene?ref=l2-shopheader-name§ion_id=18377157

BooKimi Patches are machine embroidered with 1000’s stitches! They all designed and created 100% by me! From a Sketch - Digitizing - The final product, I make them all myself. Each patch can take anywhere from 30 minutes - 2 hours to stitch! I put hours into making my designs as high quality as possible, so you can have awesome, spooky, and cute patches! - Materials: Machine Embroidery Thread, High Quality Twill Cloth, Iron-on Adhesive Backing. - Size: approx 2.75” x 3.75” - Uses: * Back Packs * Purses * T-Shirts * Jackets * Pants pockets * Hats * Blankets * Great for giving as gifts! - Iron-on backing: All of my patches come with an adhesive iron on backing. Here are some of the different ways you can apply your patches. - Iron-on: 1 - Heat iron to medium heat.(if your iron is too hot, you may risk melting, or damaging the stitches!) 2 - position your patch on material of choice. Cover with handkerchief or other cloth material, to protect the stitching. ( NEVER Iron directly on the patch!) 3 - Press on the patch firmly with your iron. Iron in circular motions for about one minute. Continue checking to make sure the patch is adhering. It may not look like it is sticking but the adhesive only sticks, when it starts to cool off. 4 - lay a heavy book or object on top, to keep the patch flat. Allow to cool for about 10 minutes. And you’re done! - Other: - for purses, or backpacks. Ironing most likely will not work. Your best option will be to hand stitch the patch onto your garment. - Make sure the material you were ironing your patch on to, is safe to use with an iron. Some material may not be able to handle the heat, and you could risk melting! - Careful befor machine wash or dry! Machine washing may distress or wear on the adhesive! And machine drying can cause the adhesive to melt due to high heat! Best way to wash: - wash on a gentle cycle, on cool or medium temp. - Layer material on a flat towel and allow to air dry.

Preach it. Stay weird, folks. 💕 Iron & Sew On ✨ 7.6cm Width 💕 2.3cm Height ✨ It's sick If you have any questions, just holla! xo Velcro stickers for patches are available and can be added to your order for free - just mention you'd like some in the notes when ordering! All shipped in eco friendly and recyclable packaging, no plastic used here.

Balloon Animal Dog iron patch for jackets Machine embroidery patch for clothes, bags, home decor, made by us in our workshop. Patch base material is made out of black material. The Color may differ from the photo. Pictured size medium. Measurements: Small patch 3.77" x 3.86" (96 x 100mm) Medium patch 4.75" x 4.86" (121 x 123mm) Large patch 5.73"x 5.87"h(145 x 149mm) Iron on instructions 1. Pre-heat iron to hottest temperature setting. 2. DO NOT USE STEAM DURING APPLICATION. 3. Surface of fabric should be clean before applying. Position patch on garment. 4. Preheat fabric where attaching patch for 10-20 seconds. Cover design with thin cloth. 5. Press straight down for 20-30 seconds with constant pressure, and then turn the garment inside out and repeat. NO BACK AND FORTH! Let cool for one minute, if edges come up, repeat. 6.There is an iron-on backing, but sewing is always recommended. design provided by urbanthreads.com Take a look at my other patches in my shop.

Got patches, but not sure how to display them? In this post, I've gathered the best ways to display patches. Check out these patch collection display ideas!

The patch is available in the following sizes. 1.5 inches wide 2 inches wide 3 inches wide Quantity : 1 PCS Made in Thailand **Before completing your order, please make sure that you have entered the correct delivery address.** ================================================== HOW TO IRON ON A PATCH ? A link to watch the video --> http://www.wikihow.com/Iron-on-a-Patch PART1 Preparing to iron on a patch 1. Figure out what type of patch you have. - Our patches come with glue on the back. 2. Examine the fabric of your clothing or accessory. - Fabrics like denim and cotton provide the best base for iron-on patches. - As a general rule the fabric you choose should be at least as heavy as the patch. - Look at the fabric care label to see whether it can be ironed (if not, there will be a crossed-out icon of an iron). If there's no label, try to figure out what material it's made of. - Be very careful with polyester fabrics, since applying the high heat necessary for ironing on patches can burn the fabric or cause it to get discolored. - Silk and other delicate fabrics are not good candidates for patches. 3. Think about design and placement. - Before you heat up the iron, lay out your jacket, sash or backpack and decided where exactly you want the patch to be placed. - If this is the only patch you intend to iron on this piece, put it in a tastefully prominent position. Make the placement look intentional. - If you're planning on ironing on more patches, like you would for a girl scout's sash or any other type of collection, plan ahead to make sure there will be room for additional patches. PART2 Iron on a patch 1. Lay the base item on a flat, heat-resistant surface. - An ironing board is useful, but if you don't have one, you may also lay your item across a doubled-up bath towel on a sturdy table. - To ensure the item will provide a good surface for the patch, iron it first. - If it's a backpack or another item that's difficult to iron, do your best to arrange it so that the part of the fabric that will be receiving the patch is flat against a hard surface. 2.Place the patch in the position you chose. The adhesive side should be flat against the base fabric. Make sure that the patch isn't crooked. - On embroidered patches, the adhesive side is the underside. 3. Heat up an iron. - Turn it to the hottest setting your fabric can tolerate. - Make sure the "steam" option is turned off, and that your iron isn't full of water. 4. Place a thin towel over the patch. - Take care not to disturb the position of the patch. The towel will protect the patch itself and the surrounding fabric. 5. Position the heated iron over the patch and press down. - Hold the iron there for about 15 seconds. Apply as much pressure as you can by pressing down firmly. 6. Remove the iron and allow the patch to to cool. - Lift the towel and check to see whether the patch is fixed on securely by gently rubbing at the edge with a finger, trying to lift it. - If it lifts up a bit, replace the towel and press it with the iron again for 10 seconds. PART3 Caring for your patch 1. Consider sewing around the edges. - For a completely secure patch, use a sewing machine or a needle and thread to secure the patch to the fabric. - This greatly reduces the chances that the patch will fall off. - Choose a thread that matches the patch. 2. Don't wash the article more than necessary. - Iron-on patches are meant to be permanent, but they do become loosened over time. - Take care not to let the article get too dirty, since washing it may cause the patch to start coming off. - If you do need to wash the item, hand wash it using cold water. Allow it to air dry.

This is a machine embroidered patch that comes with an iron on backing that can be adhered to various items such as jackets, pants, bags..... Patch measures approximately 3 x 3 inches.

100% area embroidery Mario Star Patch Size: 5.5 x 5.5 cm Iron-on patch If you want hook & loop backing see this listing: https://www.etsy.com/listing/944080971

Smiley face patch. Iron on patch Size: 2.5 x 2.5 cm For permanent use, please sew it on.

Size 2.5" X 2.75" (High X Wide) 1. Keep the back clean before ironing, and adjust the temperature to suit the clothes according to the use of the iron. 2. Put the cloth in the appropriate position (do not tear off the glue) and press it back and forth for a few times, usually about 10 seconds. 3. To prevent burns, cover the patch with a thin layer of cotton (it must be cotton, not faded cloth).After the perm check the edge to see if it is good, perm the edge more. 4 even root decal thickness to determine the temperature, a little thicker, must be higher temperature, hot time longer.For especially thick cloth stick, can be ironed a few more on the back. 5. Special note: for sequins or patches with a bright surface (since sequins are made of plastic) be sure to cover with a cloth and iron at a low temperature (below 130 ° c), or steam directly.Or cover it with a damp cloth.Lest the temperature be too high and the plastic melt. 6. After ironing, sew a few stitches on the edge of the cloth patch with needle and thread to make it more firm and comfortable. 7. If you don't have an iron at home, you can also use the same color thread to sew the cloth on your clothes. 8. Take it to the sewing shop for professional operation to avoid ironing the clothes. Shipping and Payment >>>>> Checkout more my items please visit . https://www.etsy.com/shop/Lightingstudio ........Thank you for looking......iron on patch patches for Jackets embroidery patch Patch for backpack Patches iron on Cartoon patches patches iron on Patches Pin Embroidered patches patches for hats Disney patches patches for bags

Hi! SophiePatch offers high quality Embroidery Patches and badges. With special design and pretty color, a patch will shine any thing to make a special gift. Put them on the denims, jackets, sneakers, hats, skirts, scarfs, jeans, bags, purses, wedding veils... I cannot wait to see your inspiration! How to use Iron on Patches? Turn the iron to the middle or high temperature setting, Iron the side of the bag/jacket to make sure it's warm, Place the patch where you want to attach it and over a cloth or a towel (so you don't burn the patch); Make a few rounds of ironing the patch on. Tips: Ironed on patches usually stays on for about 25 washes. To make it more stable, you might also sew on it. Contact me at any time if you have any question. All of the orders will be free shipping with standard USPS flat envelop or first class package.

Cute Chubby Calico Cat iron on patch, perfect for those who love kitties and all things cute! Our machine embroidered appliqué patches can be used to decorate your backpacks, jean jackets, hoodies, dad hats, caps, purses, shirts or anything you’d like! Iron it on, hand sew, or machine sew your patches on. You could expect beautiful embroidery of our own hand drawn designs, embroidered by us, using high quality material! ☆ Each patch is hand-cut and made in the USA. ☆ There may be a slight difference on every item that will make your items special and one of a kind. Each sweatshirt is machine embroidered on the left side. ☆ Due to different screen settings, colors may appear different! ☆ Please message us, if you have any questions or concerns! We’re here to help! 🍑ABOUT THE PATCH🍑 ☆ Patch Size - Height: 2.35 Inches x Width: 2.5 Inches ☆ Machine embroidered on Twill ☆ High quality polyester thread ☆ Due to different screen settings, colors may appear different! *** Iron or sew on to your jacket, vest, backpack, purse and more! *** 🍑INSTRUCTIONS FOR APPLYING YOUR PATCH🍑 1. Pre- heat iron without steam to temperature best for material the patch will be applied to. 2. Iron the spot you would like to place your patch on. 3. Place your patch in the desired position. 4. Place a cloth (pillowcase or heat tolerant material) on top to protect patch and your item. 5. Press the iron down for 10-30 seconds, depending on the fabric or longer if needed. 6. Turn your item inside out (if possible) and press the iron down. *** For more of a permanent stick or for thicker materials, machine sew or hand sew your patch down. *** 🍑SHIPPING🍑 ☆ All items are shipped with the United States Post Office. ☆ We are currently shipping under First Class mail. ☆ Check out our store announcements for current processing time. ☆ Free Shipping after $35 purchase. ☆ Tracking number included for all packages except stickers. *** Please make sure your shipping address is correct. Incorrect shipping addresses may be delayed. *** 🍑SIMILAR PRODUCTS🍑 ☆ Looking for other cute iron on patches? Check out our selection of embroidered patches: https://www.etsy.com/listing/1046431146/its-okay-to-cry-crying-cat-iron-on-patch https://www.etsy.com/listing/1037919011/no-thoughts-head-empty-frog-iron-on https://www.etsy.com/listing/980302342/glow-in-the-dark-angry-cat-black-cat-sew ☆ We also offer embroidery on dad hats, beanies, sweatshirts and shirts: https://www.etsy.com/listing/1240404302/glow-in-the-dark-embroidered-dad-hats https://www.etsy.com/listing/1063095133/appa-beanie-no-thoughts-head-empty-adult https://www.etsy.com/listing/1091338167/ufo-sweatshirt-alien-pizza-embroidered https://www.etsy.com/listing/1155693828/glow-in-the-dark-angry-cat-shirt-black ☆ Or if you’d like to see more cute products designed by us, check out our other small business where we specialize in digital downloads: https://www.etsy.com/shop/DigiPeachiePatches ☆ ☆ Favorite our shop to keep up with updates!

No Thoughts Head Empty Iron On Patch Each patch is hand-cut and made in the USA by us. There may be a slight difference on every item that will make your items special and one of a kind. Our machine embroidered appliqué patches can be added to decorate your backpacks, Jean jackets, hoodies, dad hats, caps , purses, shirts or anything you’d like. Iron it on, hand sew, or machine sew your patches on. www.peachiepatches.com 🍑 ABOUT THE PATCH: • Patch Size - Height: 3.22 Inches x Width: 3.17 Inches • Machine embroidered on Twill • High quality polyester thread • Due to differences in lighting on each screen, colors may appear different. *** Iron or sew on to your jacket, vest, backpack, purse and more! *** 🍑 INSTRUCTIONS FOR APPLYING YOUR PATCH: 1. Pre- heat iron without steam to temperature best for material the patch will be applied to. 2. Iron the spot you would like to place your patch on. 3. Place your patch in the desired position. 4. Place a cloth (pillowcase or heat tolerant material) on top to protect patch and your item. 5. Press the iron down for 10-30 seconds, depending on the fabric or longer if needed. 6. Turn your item inside out (if possible) and press the iron down. *** For more of a permanent stick or for thicker materials, machine sew or hand sew your patch down. *** 🍑 SHIPPING: • All items are shipped with the United States Post Office. • We are currently shipping under First Class mail. • If you would prefer a faster transit option, please send over a message for pricing before purchasing. • Due to all items being made to order, items are shipped within 1-3 business days on Monday - Friday. Days in transit are an additional 3-5 business days. We will try our best to ship out same day or next day. Check out our store announcements for current processing time. • Free Shipping after $35 purchase. • Tracking number included for all packages except stickers. *** Please make sure your shipping address is correct. Incorrect shipping addresses may be delayed. *** 🍑VIEW ALL OUR PATCHES HERE: https://www.etsy.com/shop/PeachiepatchesShop?ref=simple-shop-header-name&listing_id=877456073

This Listing Is For TWO Tentacle Iron On Patches! The Important Stuff: Dimensions: Approx 18cm x 6cm Backing: Iron On Fabric: Felt Thread: 100% Polyester Embroidered By: The Craft Rebellion in Brisbane, Australia. The Production Stuff: Due to the handmade nature of these items and that we make them to order, our production time can vary from 5 business days to up to 3-4 weeks. This is the time it takes for us to create your patches once you have placed your order. It does not include shipping time. Please check the production timeframe for your items PRIOR to purchase. The International Shipping Stuff: Our non tracked international shipping method is no longer available. All international orders are now shipped with DHL and come with tracking and a significantly shorter transit timeframe. **Please note that due to different screen and monitor configurations, colours may vary from those shown in images.

Size : 1" x 1" (WxH) (3pc) 100% High Quality | Easy to use INSTRUCTIONS HOW TO APPLY PATCHES - Spray water on the back of the logo embroidery. - Place the logo embroidery on the garment. - Set the iron temperature for cotton. - Cover the logo embroidery with a piece of damp cloth. - Iron for 18-30 seconds. - Turn the garment inside out and iron until dry.

Iron on slogan patches/ Cool for Jackets, Shirt, Backpack, and Jeans; la la la I´m not listening Patch Read the product description "how to use" guide carefully to make sure you get the skill to iron a patch on clothing easily; Put a patch on your cloth with embroidery side up; Place cotton fabric over the patch; Iron over the patch on high for about 20-30 seconds; Iron inside of cloth underneath patch for 20-30 seconds. ✭OUR ETSY STORE✭ Visit our store, we made sure to have trending items to shop for. https://etsy.me/3GVOFvt ✭MORE FROM US✭ ✭Other Embroidered PATCHES✭: If you’d like to shop for other Embroidered Patches don’t miss out on these ones. We probably have the perfect one for you or what are you looking for. ⬇⬇ https://etsy.me/3ksJL1s ✭METAL TIN SIGNS✭⇾ https://etsy.me/3QTeNLO ✭HATS/CAPS✭⇾ https://etsy.me/3krrQIy ✭POUCHES WITH PATCHES✭⇾ https://etsy.me/3XoIZRs ✭KEYCHAINS✭⇾ https://etsy.me/3QQufsa ✭WATCH BANDS✭⇾ https://etsy.me/3CZRvhD ✭BRACELETS✭⇾ https://etsy.me/3kw0K2H ✭NECKLACES✭ ⇾ https://etsy.me/3QNGOVn ✭PILLOW COVER CASES✭⇾ https://etsy.me/3XEr6xS ✭BANGLES & KEYCHAINS SETS✭⇾ https://etsy.me/3HiCDxI ✭INSIDE SCOOP✭ IG: @Flapigroupstore Facebook: https://www.facebook.com/FFlapiGroup/shop/